Tesso M Costa
e682fbcb5c
Brings the T-LoRa Pager to feature parity with the T-Deck's notification sound (built-in per-slot chimes, custom WAV playback, per-event on/off, volume, Settings > Sound UI) using the board's ES8311 codec + NS4150B Class-D amp, previously undriven. - Es8311Codec: a minimal, hand-rolled I2C register driver (DAC/output path only) rather than vendoring Espressif's much larger esp_codec_dev HAL, which this single-chip playback-only board doesn't need. Register sequence and MCLK clock-divider coefficients are derived from Espressif's public es8311.c/es8311_reg.h (Apache-2.0, credited in NOTICE). - TLoraPagerBoard::setAmpEnabled() toggles the amp around playback rather than leaving it permanently on; the existing boot-time AMP_EN drive stays as-is since it exists for shared-bus integrity reasons unrelated to audio. A boot-time I2C presence probe logs [BOOT] es8311 ok/PROBE FAILED. - UITask.cpp: pager I2S/codec playback functions mirroring the existing T-Deck ones, plumbed into the same uiPlaySlot()/uiPreviewWavFile() dispatch the other boards use (which also had two T-Deck-hardcoded call sites generalized as part of this). New CAP_SOUND_FILES capability flag gates the file-browsing sound picker without reopening real SD support (the pager remains SPIFFS-only, decoupled from CAP_SD). - platformio.ini: I2S pin flags for the pager env, confirmed against arduino-esp32's canonical pins_arduino.h for this board. Verified on hardware: boot log shows es8311 ok, and chimes/volume/WAV playback/DM+mention sounds all confirmed audible. Build-green on all three envs; Heltec V4 binary byte-identical, T-Deck flash +16 bytes. Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
A real touchscreen UI for your mesh radio. · open source · GPL-3.0
Touch-UI MeshCore companion-radio firmware for the LilyGo T-Deck / T-Deck Plus and Heltec V4 + TFT (ESP32-S3).
An LVGL touch UI — map, chat, contacts, channels, settings — split out of
meshcomod. The app depends on a
MeshCore fork via PlatformIO lib_deps.
Boards
- LilyGo T-Deck / T-Deck Plus — env
LilyGo_TDeck_companion_radio_touch - Heltec V4 + TFT + CHSC6x touch — env
heltec_v4_tft_companion_radio_usb_tcp_touch
Architecture
This repo holds only the app: the companion_radio glue, the ui-touch
LVGL UI, the two boards' glue/variants, and platformio.ini. The MeshCore
core is not vendored here — it's pulled as a library via lib_deps from the
ALLFATHER-BV/meshcomod monorepo
(the same repo as the non-touch firmware), pinned by a lean source-only core-*
git tag. The touch-app files this repo owns (TouchPrefsStore, WifiRuntimeStore,
the transports, …) are dropped from the lib via -DMC_VENDORED_TOUCH_APP so they
aren't compiled twice. The build is byte-identical to the original in-tree
meshcomod firmware.
Build
PlatformIO pulls the core fork and all libraries automatically:
pio run -e heltec_v4_tft_companion_radio_usb_tcp_touch # Heltec V4 TFT
pio run -e LilyGo_TDeck_companion_radio_touch # LilyGo T-Deck
# or just `pio run` to build both
Flash with the NVS-preserving 4-component chain (bootloader / partitions /
boot_app0 / firmware at 0x0 / 0x8000 / 0xe000 / 0x10000) so saved Wi-Fi
credentials survive — not a merged image, which 0xFF-pads and wipes NVS.
Contributing
Contributions are welcome — see CONTRIBUTING.md. One topic per PR; inbound contributions are accepted under the project's GPL-3.0 license.
License
GPL-3.0-or-later — see LICENSE. wadamesh is copyleft: anyone who distributes a build or a fork must also make their source available under the GPL. This keeps the UI open and concentrates community effort instead of fragmenting it into closed forks.
wadamesh incorporates and depends on MeshCore (MIT, © Scott Powell / rippleradios.com) and other third-party components — see NOTICE for the full list and their licenses. MeshCore-derived files keep their MIT notices; the combined work is distributed under the GPL (MIT is GPL-compatible). The MeshCore fork that wadamesh builds against stays MIT on purpose, so its Wi-Fi/BLE hooks remain upstreamable to MeshCore.