The #682 port is merged; add its env to release.sh, a flasher manifest, a
card under Seeed Studio on wadamesh.com (experimental, community port, no
device updates) and the README. The site card points at the beta feed, so
deploy the site after the next beta publishes. Board count 16.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Add the Seeed SenseCAP Indicator D1L as a new touch target. This step
builds and boots to a blank screen; the panel, touch and radio drivers
follow in their own commits so each can be reviewed against the
hardware it drives.
The SX1262's NSS, RESET, BUSY and DIO1, the LCD CS/reset and the touch
reset all sit on a TCA9535 at 0x20 on the SDA39/SCL40 bus, not on ESP32
GPIOs, so everything after this commit depends on the expander. The env
gives the radio lines virtual pin numbers 0x40..0x43 for a radio HAL to
map onto expander bits; until that HAL exists the radio is a plain
Module that links but cannot drive the chip.
The expander driver is header-only so a host test can cover it:
- its output and config shadows are seeded from the chip, because a
warm reset or the previous firmware may have left pins driven and
writing the power-on defaults back would glitch the radio, panel and
RP2040 resets;
- a failed write rolls both shadows back to the last state written in
full, and the next write brings the chip back in line with them;
- polarity inversion is cleared when a previous firmware left it set,
since it would invert BUSY, DIO1 and the strap; it is written only
when it is not already 0;
- every read of input port 0 is reported to an observer, so a DIO1 edge
is not lost when another reader clears /INT.
A five-sample majority of the P1.3 strap selects the TCXO (2.4 V) or
crystal radio at run time, so one noisy read cannot pick the wrong
oscillator.
The expander, the touch driver and the display init serialise on one
recursive mutex over the shared Wire bus (IndicatorIo::BusLock). It is a function-local static, so the compiler
guards its creation when two tasks reach the first lock together.
IndicatorIo::begin() logs the registers it inherited and names the
step that failed, since a dead expander takes the panel and radio down
with it and is otherwise silent.
The board has 8 MB of flash. The partition table has one 4.5 MB
factory app slot, a 3.375 MB SPIFFS (as on the 16 MB boards) and a
64 KB coredump, with no map tile partition. The factory slot is larger
than the 0x3E0000 OTA slots of the 16 MB boards, so an image that fits
those fits here. CAP_OTA is off: with one app slot there is no in-place
update. CAP_BATTERY is 0: no battery is fitted.
Montserrat 18/20/24 for the UI-size presets are the generated faces; the
board joins their gate in ui_font_18/20/24.c, gen-touch-fonts.sh,
hwFitFont and luaHostFigureFont. LVGL is built at -O2 with the Arabic and newlib-memcpy
settings the other envs use.
run-host-tests.sh builds every test/test_*.cpp, so the new expander
test gets its include path there in the same commit.
build-upload-monitor.sh gets --sensecap-indicator.
Signed-off-by: Confituurke <9595028+Confituurke@users.noreply.github.com>
- p4-release.sh builds and verifies the three revisions (V1.2, V1.1, V1.0)
from crowpanel_p4_101/ in the same loop as the T-Display P4 images, with
the same OTA-name and tag checks.
- Self-update is on (CAP_OTA 1): each revision updates from its own
wadamesh-crowpanel-p4-101-v1x.bin, so a V1.0 never takes a V1.2 image.
- gen-flasher-meta writes a manifest per revision; wadamesh.com gets a
CrowPanel Advanced 10.1 card with a V1.2 / V1.1 / V1.0 picker, and the
standalone flasher one card per revision. Both point at the beta feed,
so nothing shows until the next beta publishes the images.
- README, DEVICES.md and the site's board count (15).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Standalone ESP-IDF target (crowpanel_p4_101/) modelled on tdisplay_p4/, sharing its
ESP-IDF, components and esp-hosted 2.12.3 backend. Untested on hardware.
- variants/crowpanel_p4_101: EK79007 MIPI-DSI 1024x600 display (Elecrow timings,
LEDC backlight on GPIO31), GT911 touch on I2C0 45/46 (RST40/INT42), SX1262 on the
J9/J11 header with a real DIO1 IRQ, LDO3/LDO4 bring-up, C6_EN reset callback on
GPIO32, full-system-reset restart shim.
- Board revision is a build option: WADA_CP_REV=1.0|1.1|1.2 (default 1.2). V1.2 moves
LoRa DIO1/NRST from GPIO53/54 to 27/28; V1.0 has the C6 SDIO data lines reversed
(run 1-bit like Elecrow's V1.0 lesson). hostedSetPins() overrides Arduino's
generic esp32p4 SDIO pin defaults, which only match V1.0.
- LVGL at native 1024x600 with the large-screen layouts; fixed landscape.
- Shared src/: one CAP_* block in device_caps.h plus HAS_CROWPANEL_P4_101 at the P4
platform sites (storage law, SD_MMC, hosted BLE, no RTC_CNTL, no MQTT, fonts) and
the CrowPanel no-unlock-control sites. navOpenChatPanel/navGoToMainTab get
fallbacks for boards without CAP_KEYPAD_NAV.
- build.sh merge writes a 0x0 merged image per revision.
T-Display P4 still builds from the same tree.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
apps.html is generated from deploy/apps/apps.json (the catalog the devices
read) plus the site-only write-ups in deploy/site/apps-info.json, by
scripts/build/gen-apps-page.py, which deploy-site.sh now runs on every
deploy. Linked from the home page (Apps button + resource card), the SDK
guide and the sitemap.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Pins move from core-v1.17.4 to core-v1.18.0, cut from the main meshcomod
companion-v1.18.0.1 was released from. The companion changes are ported from
meshcomod's rebase into wadamesh's own MyMesh:
- onCLICommandRecv: a contact's remote CLI command runs when the user granted
that contact remote CLI, and lands in the chat as a CLI message otherwise.
- CMD_RUN_CLI_COMMAND (66) / RESP_CODE_CLI_REPLY (29) and the local companion CLI
(name, pin, Wi-Fi, radio, af/dutycycle, rxgain, tx, rxdelay, path.hash.mode,
multi.acks, board, ver), also reachable from the serial CLI. Settings without a
prefs field answer "unsupported". NodePrefs layout unchanged.
- TXT_TYPE_CLI_COMMAND is accepted for sending; sendCommandData (and our queue-
preserving wrapper) carry the text type.
- Channel data is delivered to the app (onChannelDataRecv), unsolicited responses
(pushed telemetry) reach it as PUSH_CODE_BINARY_RESPONSE, and raw-data sends
decode multi-byte-hash paths.
Clock: 1.18 seeds an unsynced ESP32 clock at 1 Mar 2026, so ClockFloorRTC's
MIN_VALID_EPOCH follows it (a set equal to the seed must stay invalid).
Pager LR1121: the AGC reset re-applies the boosted-gain setting (new core arg).
IDF builds exclude the new CommonRadioPrefs.cpp (needs <target.h>/radio_driver).
The 2 MB Heltec V4 went to 100.0% with the CLI. Its built-in language table is now
one raw-deflated blob per language (895 KB -> 312 KB), inflated into PSRAM by the
S3 ROM on first use (~10 ms, ~75 KB for the active language): 91.7% flash. Checked
on a T-Deck forced onto the table (nl, hu, el) and by the post-link key check.
Builds: all 15 S3 touch envs, Tanmatsu (3,237,024 B), T-Display P4 SX1262 + LR2021.
T-Deck boots and runs on 1.18.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Spectrum: stat tiles (peak, floor, our channel, busy), plot and waterfall drawn
at screen size (the lv_chart and zoomed waterfall were the page's render cost),
dark-to-yellow waterfall, peak hold, our-channel marker, Band/Channel and
Live/1 min/10 min chips. RF Monitor 1.4 (tiles, filled chart, typed feed, packet
detail card; the old type table did not match MeshCore payload types) and
Airtime 1.6 (big figure, tiles, duty line, rx/tx split).
Lua SDK: ui.panel, bold labels and a size-24 figure font, colors.warn/border,
app.on_audio (fires with the screen off), read-only wada.sd.list and sd: audio on
the SD_MMC boards (P4, Tanmatsu, Wio L2), caps panel/audio_events/epaper, a
"music" icon and an "audio" Store requirement. button:set() no longer writes
label fields into the button object (heap corruption, every earlier firmware).
The SDK page's input table described events the firmware never sent.
Music 1.0 (Store app): plays MP3/WAV from the card's Music folder, shuffle,
repeat, keeps going through the list with the screen off. Verified on the
T-Display P4 end to end.
Store: the update check also fetches the app catalog and badges the Store tile
with the number of installed apps that have a newer version. Baked Lua apps are
raw-deflated and inflated by the S3 ROM (14.6 KB back on the V4); the V4 language
table keeps only texts of apps it can run.
Fixes: the SD-card notice no longer fires when the card mounts fine (#667); the
Control Center clock keeps time while open (#666); M9 keyboard brightness (#664);
the battery widget's number no longer sits on a ring too small for it (Discord);
M9 shortcuts doc follows #669's composer order. New texts in all 14 languages.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
beta_93 pinned the Heltec V4 to the beta_92 .lang files because the full table
no longer fit. lang_reach.py now works out which keys any source can look up:
a .lang key is kept when it equals a C string literal anywhere in the sources
(every #if branch, adjacent literals joined, LV_SYMBOL_*/UI_ICON_* and other
string macros expanded, escapes decoded as GCC does), or that literal with TR()'s
glyph prefix stripped, or a string in any Lua app. 1818 of 1925 keys survive; the
107 dropped look unused (old dropdown strings, texts the source has reworded).
The trimmed live table is 15.5 KB smaller than the pinned one (V4 4,025,365 B
used, 37.9 KB free) and carries every translation added since beta_92.
Guards: the generator refuses to trim when an input is missing (lv_symbol_def.h,
UITask.cpp, or under 80% kept) and leaves the header alone; after linking the V4,
--check-objects reads the strings the compiler emitted and fails the build if a
translated key among them was dropped (proved by dropping a live one). The
pre-build hook regenerates on source changes too, and the header is only
rewritten when its content changes. The pinned copy is gone (git history).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
New env crowpanel_50_companion_radio_touch for the 800x480 ST7262 RGB panel,
GT911 touch and an SX1262 in the wireless slot. Board quirks follow Camillia-MT:
14 MHz pixel clock, internal-RAM draw band, PCA9557 (V1.0) / MCU (V1.1+)
backlight controller detection with GT911 reset at 0x5D or 0x14, NSS on GPIO8
(V1.2+), no SD/GPS/battery. Large-screen layouts and UI-size fonts; browser
file transfer to the internal tiles partition. Added to the upload helper,
release script, flasher manifests, site, DEVICES.md, README and NOTICE.
Co-authored-by: Copilot <223556219+Copilot@users.noreply.github.com>
Enable CAP_UI_SIZE and the font-only text-size presets (montserrat
12/14/16, 16/18/20, 18/20/24) for HAS_TDECK_PRO boards, compile the
18/20/24 px UI fonts for them, and size the status bar to match.
Docs list the T-Deck Pro and Max under Text size.
Co-authored-by: Copilot <223556219+Copilot@users.noreply.github.com>
Contact nicknames: TouchPrefsStore nick blob (48 x 38 B), display-only lookups
(contactShownName, threadShownName, senderShownName), Contact options >
Nickname on the shared text prompt (an empty OK clears it).
Control panel restyled in the launcher's tile language, with a Battery saver
tile; keyboard tooltips (navSetTip), an amber cursor and touch long-press
tooltips (the T-Deck touch read hid them on every poll).
T-LoRa Pager: M/C/A/S on Home, H/S tap and hold, Backspace = Back, N = jump to
new, held Enter = long press, per-tab focus memory, Power off confirm; LVGL
-O2 and IRAM, INT-gated keyboard, idle yield, status-bar setter guards, instant
tabs; PagerGps (u-blox software standby for rests, GPS rail cut when off),
panel sleep, amp off at boot, power-off parks the radio (NSS held), GPS, panel
and keyboard light.
Fixes: the DM duplicate check keys on the attempt and a path reset clears it,
the direct timeout masks the packed path byte, web remote hops (#636);
changelog over http (#638); Lua SDK send budgets and duplicate guard (#606);
GPS speed note (#613, CAP_GPS_BAUD_AUTO); emoji chat icon (#640); default
wallpaper (#626).
Heltec V4: Tetris, 2048 and Breakout unseeded and the built-in Lua stripped of
comments (identical bytecode), 27 KB freed; the baked language table is pinned
to beta_92's files (scripts/build/lang-pin-beta92) so it still fits.
Translations: 39 new keys in 14 languages, language store v24.
Site: theme, dark mode, aurora and guide refresh, SDK send limits, nicknames.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
lib_deps takes RadioLib ^7.6.0, and a fresh fetch now brings 7.8.1. Its
LR11x0::config() wraps driveDiosInSleepMode in its own skip for LR1110
firmware below 0x0306, so the call sits one level deeper and the patch
script no longer found it. It failed closed, stopping every M9 build at
its pre-script.
The script now knows both shapes. The patch still matters on 7.8.1:
firmware 0x0306 and 0x0307 get past RadioLib's own skip, send the
command, answer CMD_PERR and would abort radio init with -706.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_016yt7fNCKmafm9LtRjyuUmS
Frame rate: full-width PSRAM draw band (6 bands a frame instead of 14 on the
T-Deck), the still aurora drawn once and copied, LVGL at -O2 with its blend and
label loops in IRAM (scripts/build/perf_lvgl.py, 1 KB more loop stack), circle
and gradient caches, newlib memcpy. Rolled out to the M9, Attaky, RAK, Wio,
CrowPanel and V4-R8; the Pager gets the band only, the V4 the caches only.
Frame benchmark tour (DOC_PERF_BENCH) for measuring it.
Fixes: hop counts read from the packed path length (#621); Arabic shaping
rows patched in LVGL (patch_lvgl_arabic.py), Arabic 101 shift layer, kaf,
symbols, text sent as standard letters (#582); info popup colour runs that
never wrap (#602); keypad nav reaches the chat header (#623); the browser
opens the changelog (#622, gen-changelog.py at every site deploy); the
Theme background colour picker no longer edits the accent; flasher entries
for P4 units with factory ESP-AT Wi-Fi chips (#612, #619).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Home is a grid of arrangeable widgets (24 kinds, presets, a layout per
orientation, Lua app widgets via wada.widget); Unread, Chat and Mentions
get a large size. Theme > Background puts an aurora (still by default, or
moving), a colour, a picture or nothing behind every screen, with glass
cards and a smoked-glass top bar. A GPS icon in the bar, a GPS battery
saver (u-blox GNSS stop/start where there is no power switch), and a
battery saver that no longer waits for Bluetooth and Wi-Fi to be off.
Also: navigation bar position, every settings page on the redesign's
cards, a faster app drawer, slower screensaver drift for burn-in, text
wrapping at spaces only, the V4-R8 Store Apps tab, and SDK Test marked
extended-SDK only (keeps the 2 MB V4 at 99.8%).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Every screen redesigned to the Oct 2026 mockups, on one design system:
palette, type roles (generated Montserrat faces with Lucide line icons on the
LV_SYMBOL codepoints), a theme apply-cb that styles every LVGL widget, button
kinds, list rows, sheets as action lists, toasts and key-glyph avatars.
Rebuilt: status bar, Chats (filters, + and menu), conversation (route header,
hop meta, "Heard by N repeaters", delivery states, pill composer), lock screen
(mark, clock, 24 h activity, unread cards), Constellation screensaver, Home
launcher and launcher sheet, Status page, grouped Settings home, animated boot
splash, and the message glance as a notification card.
New: optional PIN lock (salted SHA-256, keyboard / touch pad / number pad per
board, backoff that survives reboot), screensaver on battery with its own
duration, T-Deck text sizes, trackball hold to switch Scroll and Cursor (Scroll
default, prefs v69/v70), hold Settings tab for the control panel. M9 bottom
notices removed. Every screen measured for the Large and Huge text sizes.
Fix: adverts over 2/3-byte path hashes never reached the recently heard table
(packed path_len compared as a byte count); ADVERT_PATH replies now carry the
whole multi-byte path.
English placeholders for the 204 untranslated keys in every .lang file.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The T-Display P4 ships EIGHT images: panel (AMOLED/LCD) x radio (SX1262/LR2021)
x C6 stack (esp-hosted/ESP-AT). The C6 axis is new and it is the dangerous one,
because the two builds are identical apart from the artifact name they carry,
and flashing the wrong one at an older unit used to boot-loop the board.
scripts/build/p4-release.sh builds all eight and VERIFIES each image against the
OTA name baked into it before accepting it. That is the same string the device
builds its self-update URL from, so a disagreement with the filename is exactly
the failure that bricks people -- the T-Deck Max self-updating to Pro firmware,
and this table has been wrong three times. A mismatch aborts the release.
It earned that check immediately: building the eight by hand produced two
mislabelled images, and every mechanism meant to prevent it was itself broken.
* build.sh fullclean has NEVER worked from a plain shell. It ran `cmake -E
remove_directory` above the esp-idf/export.sh that puts cmake on PATH, so it
printed that it had removed the tree, exited 0, and removed nothing. Now a
plain rm -rf, and it verifies the directory is gone instead of assuming.
This matters beyond tidiness: the hosted and ESP-AT builds SHARE a build dir
(the C6 axis does not change P4_BUILD_TARGET), the backend is read from the
environment at CMake CONFIGURE time, and CMake does not reconfigure because
an env var changed -- so a clean that silently did nothing yields an
incremental build of the OTHER variant, with no configure output to show for
it. That is precisely how the two mislabelled images were produced.
* Deleting CMakeCache.txt alone is not a clean either; it leaves CMakeFiles/
behind and the next configure dies in CMakeDetermineCCompiler.
* Detecting failure by grepping a log for "error:" misses a failed CMake
configure, which prints "Configuring incomplete" and no such line -- and the
previous application.bin is still sitting in the directory to be picked up.
Exit codes now.
gen-flasher-meta.py gains the four ESP-AT entries, labelled "older unit, ESP-AT
C6": someone choosing in the web flasher has no serial log and needs to pick on
something they can check.
scripts/run-host-tests.sh runs test/ as one command. Nothing ever did, which is
why test_touch_prefs_schema had been failing to COMPILE since v64 appended
report_ping and report_done_n without updating its sums -- and a static_assert
that does not compile is not a guard. That one exists to catch the mid-struct
insert that broke v44 and shipped the poisoned beta_57 layout. Repaired, with a
note where the next person appending a field will read it. 17 pass, 0 fail, 2
skipped with their reasons stated rather than quietly dropped.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
- New crowpanel_35 variant: display, SD, board and target files, plus board JSON
- Portrait mode is drawn rotated 180°; landscape stays at rotation 3
- Share the GT911 touch driver between Wio Tracker L2 and CrowPanel
(WioTrackerL2Touch.cpp -> src/helpers/input/LgfxGt911Touch.cpp)
- platformio envs, flasher/site entries, release and merge-bin support
- Tests for the CrowPanel SD codec and merge-bin
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0132MkJ7RUV32mV9F7o4PJMm
Settings, About gains "Report this build": works or a problem, five tick
boxes for what you actually exercised, how long you have run it, an optional
line. It posts to the report service and lands on wadamesh.com/beta, which is
what the next promote is decided on. Ticking matters: "it works" from somebody
who watched it boot and "it works" from somebody who messaged on it all week
are not the same claim, and a board only goes green on two of the second kind.
"Report a bug" draws a QR for a prefilled GitHub issue form. The issue is filed
from the reporter's phone under their own account, so no write token has to
exist in a public firmware image and the reporter gets the replies.
"Count this device" is off by default. It lets the update check say which board
and version it is running, so a board with no reports can be told apart from a
board nobody owns. Those need opposite responses and nothing could tell them
apart before.
Mechanics: the POST rides the existing core-0 tile/update worker and its
WiFiClient/HTTPClient, like the version check, because a second pair on that
~8 KB stack overflows it. The device id is a salted SHA-256 of the public key
truncated to 64 bits, so a second report replaces the first without saying who
sent it. Sending is two taps and the second lists every field that leaves.
Prefs v64 appends report_ping + report_done_n at the tail, which the schema's
trailing static_assert now checks.
Also here: scripts/build/matrix-check.sh prints what testers reported for a tag,
and release.sh runs it before a --promote. It never blocks; a board nobody owns
can never go green. With no reports at all it now says so rather than reporting
a clean bill of health, which is the habit this is meant to replace.
Built on all eleven S3 envs and the T-Display P4.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
A board added mid-cycle (the T-Deck Max) has no images in an older tag, so
promoting that tag copied a file that does not exist and, with set -e, took
the whole promotion down. It is skipped with a note now, and the flasher
manifest generator leaves out any board with no image in the channel it is
writing, rather than handing the flasher a 404.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Review of #531 turned up four things that had to be fixed before release:
- An unusable region name no longer discards the radio settings. The save
returned early, so frequency, bandwidth, SF, CR and TX power were thrown
away, and the rule rejects names with capitals or a "$private" scope, so
anyone carrying an older region could not change their radio at all. On the
pager that path is the silent blur save, so it failed with nothing on screen.
Now only the region is skipped, and it says so.
- Restored useChainedFont() on the telemetry Show button: without the fallback
chain that label is boxes in Russian, Ukrainian, Bulgarian, Serbian, Greek.
- Region scanning installs unknown repeaters as transient contacts so their
encrypted replies can be matched. They were never removed, so each scan left
up to 16 nameless entries in the contact table (and in Contacts). They are
dropped when the scan ends or the page closes.
- One radio request per scan tick. The loop ran through all 16 repeaters in a
single 200 ms tick, which is that many key derivations back to back.
The V4-R8 also did not build (its src/ files see a vendored lv_conf.h, so the
new text-size fonts were missing) and then did not fit at 101.3%. It builds at
85.6% now: the board no longer carries the compiled-in translations it
inherited from the V4, which it never needed, since with 8 MB of PSRAM its
store works like any other 8 MB board.
T-Deck Max (#545) joins the release matrix: build list, flasher manifest,
DEVICES.md and the site's board list. Board names in the flasher lost their
em dashes.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Pressing down past the last message page-scrolls the chat list with an
LVGL animation. In a long chat the list uses compressed scroll
coordinates, and chatVirtRemap1To1Scroll re-anchored the position on
every LV_EVENT_SCROLL with lv_obj_scroll_to_y(LV_ANIM_OFF). That deletes
the running animation from inside its own step. LVGL 8.4 reads the
animation again after the step, and when the step was also its last
(the UI loop was busy for longer than the animation) it finished the
freed animation and freed it a second time. By the next round that
memory belonged to something else, and anim_timer called a garbage
get_value_cb: the jump to 0x00020000 in the beta_79 and beta_80 M9 dumps,
both at the same call site.
- chatVirtRemap1To1Scroll follows a scroll that an animation drives and
leaves the re-anchor to chatVirtOnScrollEnd. The page scroll now also
completes on long chats; the early re-anchor stopped it after a frame.
- scripts/build/patch_lvgl_anim_uaf.py skips LVGL's completion check when
the animation list changed during the step, as LVGL 9 does. Applied to
every touch env as a pre-script and to the vendored P4 copy
(fetch-deps.sh, build.sh). Idempotent, fails closed on source drift.
- test/lvgl_anim_uaf/run.sh reproduces it on the host under
AddressSanitizer: stock LVGL with the old handler reports the
use-after-free in anim_timer, and either fix alone runs clean.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Adds LilyGo_TDeck_Pro_companion_radio_touch to release.sh (as
wadamesh-tdeck-pro), a flasher manifest labelled "(experimental)", and a
website card following the V4-R8 pattern: experimental in the heading,
"Partially supported", beta only.
The card says plainly what is known: contributed through #469, all the main
hardware works, but it has been tested on a single v1.1 unit, v1.0 units are
the least proven, and the e-paper display redraws rather than updating
instantly.
The site is not deployed with this commit: the card's install button points at
manifest-tdeck-pro.json, which only exists once a beta containing the board is
published.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The PR added the board and its env, which makes it build. It does not make it
ship. Three lists decide that and none of them knew about it: release.sh ENVS
(what gets built and named into a release), gen-flasher-meta.py BOARDS (which
manifests the web flasher gets) and the flasher page itself, which lists boards
by hand.
Without these the board compiles cleanly forever and never appears in a release
or on the flasher, which looks like nothing is wrong.
Named wadamesh-wio-tracker-l2, its own Seeed Studio section on the flasher,
marked beta-channel-only like the Attaky was on arrival, since stable is still
beta_65 and this board has never been in a stable build.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
oumike. ESP32-S3, 16 MB flash, 8 MB octal PSRAM, quad-SPI 320x240 panel via
LovyanGFX, GT911 touch, SX1262 at 22 dBm, GPS, microSD on SD_MMC. New board
file, new variant, one new env. Seeed start selling it next week and the
maintainers have the hardware; we do not.
Merged on their hardware bring-up rather than ours: display, touch, GPS,
microSD, battery and buttons are confirmed on-device by the author. What this
side can prove is that it does not cost anyone else anything, so the whole
matrix was built: all nine S3 envs including the new one, plus both ESP32-P4
targets.
The PR also carries accumulated touch-UI work from the author's development
line, which he flagged himself and offered to split out. Merged as-is because
the three-way merge came through with zero conflicts and nothing from today was
reverted: the prefs schema is still v54, and kb_force_legacy, boot_wifi_open,
the P4 gpsEnsureBigRxRing fallback and the chat-store migration logging are all
still present. Verified explicitly rather than assumed, since the diff against
main showed 1706 deletions purely because the branch predates today's merges.
Two bring-up findings worth keeping: Arduino's Serial1.setPins() takes (rx, tx),
so PIN_GPS_TX is the pin we receive on -- the same naming trap the V4-R8 and
Pager envs already carry, and it left this board's GPS listening on a silent
pin. And the panel is fixed landscape (CAP_ROTATABLE 0), so the keyboard's
rotate arrows are not built there.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
pisti87 read v18 and called it chaos. He was right, and it was mine.
Two defects in the extractor I added yesterday:
- It joined every string literal in a call argument, so a ternary became one
key. `cut ? "Paste (move)" : "Paste (copy)"` shipped as the single key
"Paste (move)Paste (copy)", and with it "Unblock Block",
"Unfav Favorite", "Other networksNetworks", "Batteryactivityon" and
"Stop sharing loc Share my loc". None of those strings exist anywhere in
the firmware. Literals are now grouped only when genuinely adjacent, which
is what the compiler concatenates, so both branches become their own key.
- It scanned raw source, comments included. That is how "Geblokkeerde
gebruikers" -- Dutch, appearing only inside a comment about how a long
translation degrades -- became a KEY in the Hungarian file. Comments are
stripped now, string literals preserved.
202 invented rows removed across the thirteen files. Only rows that were both
unknown to the extractor AND still untranslated were touched, so no
translator's work could be lost either way.
Also his: the curly quotes in the Hungarian credits render as boxes because no
bundled font carries U+201E/U+201D. Five values de-curled. And five strings he
found raw are wrapped: the Wi-Fi rescan and hidden-network rows, the update
check, and the downgrade prompt. The two Wi-Fi rows build their label at
runtime, since TR() returns a pointer and cannot join a glyph literal at
compile time.
Languages go to v19. v18 is deleted rather than left behind: it was only ever
correct for about a day and everything in it is superseded.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
cvhviz. The M9's magnetometer was documented on the board and nothing had ever
talked to it. The driver is written from the datasheet's register map rather
than SensorLib, whose setOutputDataRate() writes the ODR into the OSR bits, and
the axis orientation is measured on hardware at four headings rather than
inherited from a declaration Meshtastic marks unverified and never uses. The
+-32 G range looks absurd for a 0.5 G planet until you measure the board's own
hard-iron bias at about 7x Earth's field.
Also carries several fixes found while testing on hardware: every Lua app opened
on a white page on keypad-nav boards (the focus highlight harvested the app body
as a target and reverse-video filled the page), a use-after-free in the Lua net
worker when an app closed mid-request, an unfreed http_get buffer, canvas pixel
buffers GC'd while LVGL still drew from them, one RTC I2C read per contact, and
map re-open costing 2.5 s on every visit.
Three changes on merge:
- The map tile-keep gate read `total && total < 4 MB`, so a board reporting
zero PSRAM -- the most constrained case there is -- landed on the roomy side
of the test and kept its tiles. Dropped the non-zero guard.
- gpscompass is 55 KB of Lua, more than every other app combined, and it wants
a magnetometer the seeded boards do not have. The author deliberately left
it out of lua_builtin.h; that intent now lives in the catalog as
"seed": false rather than in whether someone remembers to regenerate, since
the generator runs from a pre-build hook as of this branch.
- consoleModeToggleCb was defined inside a !HAS_TANMATSU region while the
Settings row that binds it compiles on every board, so the Tanmatsu link
broke. Moved it out. The console boot path is gated on CAP_CONSOLE alone, so
the switch now does what it says there too.
Built on all seven S3 envs plus both ESP32-P4 targets.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
pisti87 reported a long list of text that stays English whatever the language,
and said the strings were in his language file and still did not appear (#257).
Both halves are true, and the reason is the audit.
The extractor only ever recognised TR("literal"). Three very common shapes were
therefore invisible:
mk_row_btn("Reload tiles in view", cb) // helper TR()s its parameter
for (auto& r : rows) TR(r.label) // literal lives in a local table
TR(contactsSortOptName(m)) // helper returns one of several
All three translate correctly at runtime, so the source looks properly wrapped.
But the literal at the call site was never emitted as a key, so it never entered
a .lang file, so no translator could ever supply it -- and adding it by hand
did nothing, because the audit's key list is what the files are checked against.
That is 51 strings across the map options sheet, the sort sheets, the contacts
filters and the home launcher.
The audit now understands all three, plus tr("...") in the Lua apps, and the
newly visible keys are in all thirteen files as placeholders so translators can
see them. 1017 keys, up from 966.
Four strings were genuinely raw and are now wrapped: the reader's idle status,
the Discover empty feed, the crash-report export button and Paste (move/copy).
Lua apps had no way to translate anything at all, so every built-in was hard
English regardless of the device language. wada.sys.tr() gives them the same
table the interface uses; airtime 1.4 is the first to use it, with the
`sys.tr or identity` fallback so it still runs on older firmware.
Two more instances of the drift this issue is really about:
- gen-lua-builtin.py read out/firmware/apps/, which nothing writes -- the
deploy rsyncs deploy/apps/ straight to the VPS. So the mirror was stale and
the two apps added in beta_68 were never baked in: boards that cannot reach
the Store shipped without them. It reads the canonical directory now, and
regenerates from the same pre-build hook as the language table.
- Baking a row whose translation equals its key does nothing, since TR()
returns the key on a miss. Skipping them takes the header from 1.11 MB to
939 KB and gives the V4 back 16 KB of flash, which matters at 89%.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The map About/credits sheet was 820 bytes of raw English built with snprintf and
no TR() anywhere in it, so it stayed English in every language (#257). It is now
three keys: the two attribution headers (the OpenTopoMap variant is credited
separately because its style is CC-BY-SA) and the body, kept whole rather than
split per paragraph so translators get prose instead of fragments. The buffer
grows 820 -> 2048 because Hungarian runs about 1.5x English here and the
Cyrillic and Greek files are two bytes a letter.
Hungarian text from pisti87 (#257). Two edits to what he posted, both flagged on
the issue: the hard line breaks he inserted at the English wrap points are gone,
because the label wraps itself and a fixed break lands mid-sentence on any other
panel width; and the header reads "Terkep adatok" rather than "Map adatok",
which looked like a copy-paste artifact given the rest is fully translated. The
OpenTopoMap variant is derived from his own wording and is his to correct.
Also raw, from the same report: the Discovered auto-add hint and the four type
words it interpolates. The hint buffer goes to 240 bytes and the type list to
128, since the translated plurals are longer than "chats, repeaters".
The reason none of that would have shipped: gen-lang-builtin.py exists so the
baked-in table and the .lang files the store serves cannot drift, and its
docstring promises a pre-build step that runs it. Nothing ran it. Editing a
.lang and building produced an image carrying the OLD translations, silently.
It is now a real pre: hook on all seven PlatformIO envs and a line in both IDF
build scripts, regenerating only when a .lang is newer than the header.
deploy-apps.sh grew the matching check for the other half of that path: a
catalog version that disagrees with the file's own "# ver:" publishes
translations to a version no device asks for.
All thirteen languages snapshot to v17 -- the merged region and SD work added
keys to every file, not just Hungarian.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
pisti87 asked whether the obsolete entries in the language files will be removed
(#262). Measuring it first was the right move, because the tool that would have
driven that cleanup was wrong.
source_keys() only ever matched TR("literal"). Strings reached indirectly, as in
TR(kSettingsCats[c].label), were invisible to it, so every settings-category name
looked unreferenced: About, Backups, Language, MQTT bridge, App permissions and
the rest. Anyone pruning the .lang files on that output would have deleted live
translations for some of the most visible labels in the UI.
The audit now also pulls literals out of any table whose name appears inside a
TR(...) subscript. Deliberately greedy: over-collecting keeps a translation alive,
under-collecting deletes one.
That immediately found a real gap it had been hiding. "App permissions", the
settings category added with the permissions page, was missing from all 13
languages and the old audit reported everything as covered. Added, builtin
regenerated, published as language v15.
Also adds --obsolete, the reverse check pisti87 actually needs: rows in each .lang
file that no TR() key matches. It reports and never deletes, and says plainly that
these are candidates to check rather than a delete list, for the reason above.
Numbers now: 950 keys reachable, hu.lang carries 1044 rows, 94 unreferenced. The
earlier figure was 119, so 25 of those were the false positives just fixed.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Second 7-dimension adversarially-verified audit over the 08-19 tree.
Headliners: SUB_MAP over a display-only Lua app orphaned the app page
(key-only soft-lock); Back-ladder z-order redesign (CC/power always-
frontmost, confirm-modal deference, Lua key-forward suppressed while a
confirm is up — the send-permission dialog was unanswerable); map pan
flag could go stale across tab jumps/popups; null-close progress rows
now genuinely block the registry dismiss (shared fix); terminal RX
mirror, fullscreen title, wallpaper caption, storage-error guidance
widened to M9; accent/@-mention pickers suppressed (dead chrome on a
touchless board); kb-backlight cache only latches ACKed duties (0xFF
sentinel == duty 255 skipped the first write every boot); deep sleep
actually drops the rails now (display refcount, LEDC pin re-route,
RTC/digital holds) and powers off radio+GPS; TCXO fallback no longer
codifies the disproven 0.0f; RadioLib old-FW patch fail-closes at
link; ENV_SKIP_GPS_DETECT + CORE_DEBUG_LEVEL=0 added to the env.
Full round log in M9_PORT.md 'Audit pass 2 (2026-08-20)'. All four
touch envs (M9, T-Deck, V4-R8, pager) compile clean.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
pisti87 found "Settings → Quick replies" drawing a tofu box, in English as well
as Hungarian. It is not a language bug and it is not the beta_62 fallback-chain
fix falling short — the glyph simply was not in any font we ship.
gen-touch-fonts.sh asked $noto_sans for the symbol set, and Noto Sans does not
contain U+2190-2193 or U+2260/2264/2265 (verified directly against the release
the script pins). lv_font_conv omits a glyph its source font lacks rather than
failing, so those seven characters silently never made it into extras_font_*,
in every language, since the fonts were first generated this way.
Scope is much wider than the one line reported: 137 uses of → in the touch UI
plus arrows in all 13 .lang files. pisti87 happened to open one of them.
Fixed by cutting the seven from Montserrat, which has all of them, is already
the primary UI face and already the first --font in this script — so no new
dependency, no new licence line, and the arrow matches the text beside it. They
had to be REMOVED from the Noto Sans symbol list as well: with the codepoint
claimed by a later font that cannot supply it, the Montserrat pass produced
nothing and the regenerated files came back byte-identical apart from a comment.
Noto Sans Symbols 2 was the obvious candidate and does NOT have them either —
it errors outright when asked, which is how that was ruled out.
Not visually confirmed: I have no way to see the glyph render from here. The
regenerated fonts grew ~390 lines per size and lv_font_conv accepted the request
(it hard-errors when the source font has none of the symbols, as Symbols 2 did),
so the glyphs are in. Worth a look on a device before the beta ships.
Reported by pisti87.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
pisti87's T-Deck rebooted every time he logged into a repeater, but only in
Hungarian. The login clock-skew warning does:
snprintf(msg, n, TR("Device clock differs from \"%s\" by %lu min%s"),
name, minutes, suffix);
and the Hungarian row reordered the conversions to "%lu ... %s ... %s". Varargs
are positional, so snprintf read the name POINTER as an unsigned long and then
took the minute count -- the integer 3 -- as a char* and dereferenced address 3.
Instant panic, every login, Hungarian only. English fit the declared order, so
it never showed there.
Fixing the four bad Hungarian rows is not sufficient: TR() returns a format
string and translations come from .lang files that users download or hand-write,
so any file can crash any device. TR() now compares the ordered conversion
signatures of key and translation and falls back to the English key on a
mismatch -- the key IS the call site's format string, so it is always correct.
The scan runs only for keys containing '%', which is a small minority.
Also fixed the four rows (three were Hungarian-only crashes or dropped values),
bumped hu to v11, and taught audit-lang.py to fail the build on a mismatch so a
future translation PR cannot reintroduce this. Unit-checked that the audit
detects the original bad row and accepts the repaired one.
Reported by pisti87.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The firmware asked for these keys and no .lang file carried them, so they
rendered English in all 13 languages with nothing to show a translator that
they were missing. Mostly strings that shipped with a feature whose PR did not
touch the language files: the SD arbitration and migration warnings, the
Wi-Fi/BLE coexistence messages, the keyboard-navigation vocabulary
(Up/Down/Left/Right/Select/Scroll) and section names (General, Clock & time,
Sensors, Screen, Home, Messages, Keys, Compact, Snake).
They go in with an EMPTY translation, which is the format's own way of saying
'not translated yet': the runtime loader requires a non-empty value
(`if (*p && tab[1])`) and gen-lang-builtin.py requires `if k and v`, so both
skip these rows and the English falls through exactly as before. Confirmed:
i18n_builtin.h regenerates byte-identical. No `# ver:` bump for the same
reason — device behaviour is unchanged, so there is nothing to re-download.
Also fixes the audit's own row parser to match the loader: a line is a comment
only when it has NO tab. Testing for a leading '#' hid every key starting with
LVGL recolor markup ("#7A7F87 Wardrive: …#"), the exact class the loader has a
comment warning about.
Every language is now at 0 missing keys.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Nothing checked this. The .lang files are hand-maintained and i18n_builtin.h is
generated FROM them, so drift is invisible in both directions: a row whose
English no longer appears in any TR() call is translated for nothing, and a
TR() key with no row renders English in every language forever.
Matching mirrors TR() in i18n.cpp, which is the part a grep gets wrong —
adjacent C literals concatenate, LV_SYMBOL_* icon prefixes are stripped before
lookup, non-ASCII is often written as \x escapes, and menu/tab labels reach
TR() through a table field rather than as a literal (resolved by harvesting the
table's initialiser).
Current state: 910 TR() keys; every language carries ~57 dead rows and is
missing ~53 keys (hu: 77 dead, 52 missing).
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
