The R8 env shipped HELTEC_V4_BUZZER_PIN=-1 because the Kit V2's PAM8904 wiring
was unconfirmed, so R8 users have never heard a notification. Heltec's
Expansion_board_V2.03.pdf schematic settles it: DIN = GPIO4, and EN1/EN2 are
hardware-strapped high (10K pull-ups, 3x boost) with DIP switch SW1 as a
hardware mute -- no enable code needed, the stock V4 tone() chime drives DIN
directly. GPIO4 is unclaimed on the R8 (board I2C moved to 17/18).
Tester-verify: chime on message. If still silent, SW1 on the expansion board
is the hardware mute -- check it is not switched to ground.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* attaky_mesh_series: add board variant with FT6636 touch and landscape UI
* attaky_mesh_series: P3 battery (MAX17048) + GPS + shared-I2C mutex
- AttakySharedI2C: one Wire.begin() + a mutex serializing the shared board
I2C bus (SDA=2/SCL=1) across the FT6636 touch poll (core 0), the MAX17048
fuel gauge (core 1), and the future AW9523 keyboard. Arduino's TwoWire
buffers are not concurrency-safe.
- board.begin() owns the authoritative bus init; the touch driver now takes
the lock around every transaction instead of its own Wire.begin().
- getBattMilliVolts(): real MAX17048 VCELL read (78.125 uV/LSB -> mV = raw*5/64),
2 s cache + lock, replacing the 4000 mV stub. Upstream maps mV -> % itself.
Hardware-verified ~4058 mV.
- GPS: rename the dead GPS_BAUD flag to GPS_BAUD_RATE (the core reads that; 9600
only worked via the #else default). Pins verified on hardware: ESP RX = IO17
receives ATGM336H NMEA; MeshCore's module-centric PIN_GPS_TX=17 maps correctly.
* attaky_mesh_series: Control_Keyboard_(Bottom) dual-AW9523 keyboard
Add the Control_Keyboard_(Bottom)_1.0 module as an ADDITIVE hardware
keyboard on the touch board. Two AW9523 expanders (0x5A left / 0x5B
right) each scan a 5x5 matrix over the shared board I2C bus, serialized
through the AttakySharedI2C mutex alongside the FT6636 touch poll and the
MAX17048 fuel gauge.
The driver emits final bytes (printable ASCII, backspace, enter, space)
with momentary Shift resolved to uppercase in-driver. UITask injects them
into the focused textarea exactly like the web-mirror keystroke path, so
CAP_KEYBOARD stays 0 and the on-screen keyboard is not suppressed (touch
typing does not regress). Focus-gated: the matrices are only scanned
while an editable field is bound, so a key has zero side effect when
nothing is focused.
Hardware-verified, both halves: q/w/e/r/t (0x5A) + y (0x5B), Shift
uppercase, backspace, space, enter; on-screen keyboard intact.
* attaky_mesh_series: use reliable 115200 upload speed
* attaky_mesh_series: use core default GPS baud
* attaky_mesh_series: restore GPS_BAUD setting
* attaky_mesh_series: rename PlatformIO environment
Full keyboard+encoder-driven board port: TCA8418 QWERTY matrix, rotary encoder
focus-nav, ST7796 display, ES8311 notification sound, both radio variants.
Hardware-verified by the author against a live mesh.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
# Conflicts:
# src/ui-touch/UITask.cpp
The V4-R8 uses an ESP32-S3R8 (8 MB OCTAL PSRAM) which claims GPIO33-37, so
Heltec moved every control signal off them and the Expansion Kit V2 rebuilt the
display/touch/SD block onto a hardware-SPI bus:
Vext 36->40 (active-LOW) . GPS_EN 34->42 . LED 35->46 . ADC_Ctrl removed
TFT (LovyanGFX HW-SPI): MOSI=15 SCK=16 MISO=45 CS=47 DC=48 RST=21 BL=44
touch (CHSC6x, shares board I2C 17/18) . micro-SD (shared TFT SPI, CS=3)
The build defines HELTEC_LORA_V4_TFT too, so it reuses all the V4 touch-UI code;
HELTEC_LORA_V4_R8 gates only the deltas. 8 MB enables the on-device web browser
(CAP_WEB_BROWSER) and the SD card (CAP_SD). Also wires the board into the release
+ web-flasher pipeline (release.sh, gen-flasher-meta.py, the flasher picker).
UNTESTED — no V4-R8 hardware yet. Pin sources: Meshtastic heltec_v4_r8 variant,
Heltec V4-R8 pinmap, and the Expansion_board_V2.03 schematic. All three touch
envs build clean; V4/T-Deck unregressed. On-device TODO: CHSC6x shared-Wire on
17/18, SD_CS=3, and the V2 PAM8904 buzzer.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Milestone 10: serve pager units sold with SX1262 instead of LR1121.
Same board JSON, same variant dir, same NSS/RESET/BUSY/DIO1/SCLK/MISO/
MOSI pins as the LR1121 env -- confirmed against trail-mate's own
working SX1262 pager reference that it's the same physical radio slot,
just a different chip populated. RADIO_CLASS/WRAPPER_CLASS swap to the
core fork's CustomSX1262/CustomSX1262Wrapper, the exact same generic
classes the T-Deck already uses, so radio_init() just calls
radio.std_init(nullptr) -- no new radio C++ code needed, only build
flags.
TCXO voltage and the DIO2-as-RF-switch setting are NOT copied from the
T-Deck wholesale: trail-mate's reference for this exact PCB uses
RadioLib's own 1.6V TCXO default with no override, so
SX126X_DIO3_TCXO_VOLTAGE is left undefined here too (std_init() already
retries at 0.0f on an SPI-cmd failure). SX126X_DIO2_AS_RF_SWITCH=true
and SX126X_CURRENT_LIMIT=140 ARE carried over from the T-Deck, but
because both are tied to the shared LORA_TX_POWER=22 target (RadioLib's
default 60mA current limit silently caps real TX power below 22dBm on
any board, not something T-Deck-specific), not board-specific analog
circuitry.
Also fixes a real bug found compiling this for the first time:
target.h only ever included the LR1121 wrapper (vendored locally in
this variant dir), never the core lib's CustomSX1262Wrapper -- unlike
T-Deck/Heltec V4's own target.h, which already include it. RADIO_CLASS/
WRAPPER_CLASS resolved to nothing and every radio_driver.* call site in
MyMesh.cpp failed to compile.
Hardware-verified: flashed a real SX1262 unit via the documented
out-of-box recipe (full erase + merged image), boot log confirmed
radio init succeeded alongside the rest of the board, and a live
mesh test confirmed send/receive on the public channel, a custom
channel, and DM.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
- PIN_USER_BTN: -1 -> 0 (enable BOOT key on GPIO0)
- Short press (<1s): toggle screen on/off (no hard-lock)
- Long press (>=1s): open power menu (Power off / Reboot / Cancel)
- Add ARDUINO_USB_CDC_ON_BOOT=1 (stable USB CDC COM port)
- boards/rak_tap_v2.json: use_1200bps_touch=false, wait_for_upload_port=false
(manual download mode via BOOT+RESET, esptool upload on COM7)
- Remove unused boards/wiscore_rak3312.json
- Remove LovyanGFX from Heltec lib_deps (accidental regression in baseline)
Signed-off-by: Ethan-chen1234-zy <ethan.chen@rakwireless.com>
Brings the T-LoRa Pager to feature parity with the T-Deck's notification
sound (built-in per-slot chimes, custom WAV playback, per-event on/off,
volume, Settings > Sound UI) using the board's ES8311 codec + NS4150B
Class-D amp, previously undriven.
- Es8311Codec: a minimal, hand-rolled I2C register driver (DAC/output path
only) rather than vendoring Espressif's much larger esp_codec_dev HAL,
which this single-chip playback-only board doesn't need. Register
sequence and MCLK clock-divider coefficients are derived from Espressif's
public es8311.c/es8311_reg.h (Apache-2.0, credited in NOTICE).
- TLoraPagerBoard::setAmpEnabled() toggles the amp around playback rather
than leaving it permanently on; the existing boot-time AMP_EN drive stays
as-is since it exists for shared-bus integrity reasons unrelated to audio.
A boot-time I2C presence probe logs [BOOT] es8311 ok/PROBE FAILED.
- UITask.cpp: pager I2S/codec playback functions mirroring the existing
T-Deck ones, plumbed into the same uiPlaySlot()/uiPreviewWavFile()
dispatch the other boards use (which also had two T-Deck-hardcoded call
sites generalized as part of this). New CAP_SOUND_FILES capability flag
gates the file-browsing sound picker without reopening real SD support
(the pager remains SPIFFS-only, decoupled from CAP_SD).
- platformio.ini: I2S pin flags for the pager env, confirmed against
arduino-esp32's canonical pins_arduino.h for this board.
Verified on hardware: boot log shows es8311 ok, and chimes/volume/WAV
playback/DM+mention sounds all confirmed audible. Build-green on all three
envs; Heltec V4 binary byte-identical, T-Deck flash +16 bytes.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
Boot TX power was left at a conservative 10dBm (Heltec V4's pattern) with
no way to raise it, unlike the T-Deck which boots straight at the chip's
real 22dBm ceiling. On hardware this was silently degrading outbound
range: adverts/DMs sent from the pager were unreliable while inbound
reception was fine, since the far node's own TX power was unaffected.
22dBm is confirmed as this chip's actual sub-GHz HP-PA ceiling via
RadioLib's LR1120::checkOutputPower() (LR1121 inherits it) and matches
trail-mate's own working config for this board.
Also widen the three RX-boosted-gain gates in MyMesh.cpp/DataStore.cpp
that only checked USE_SX1262/USE_SX1268 to include USE_LR1121 --
CustomLR1121Wrapper already implements setRxBoostedGainMode/
getRxBoostedGainMode, so the setting was silently a no-op for this radio.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
Six real bugs found and fixed across two hardware sessions (full account in
TLORA_PAGER_M7_HW_DEBUG_LOG.md): stale-NVS BLE bond crash, no screen-wake
path for keyboard/encoder input, wrong TFT_eSPI SPI-port index on ESP32-S3,
missing panel INVON for this ST7796 batch, two SPI hosts fighting over the
shared radio/display pins, and a floating XL9555 ch6 panel hardware-reset
line (the actual root cause of the intermittent black screen, not the SPI
race originally suspected). TLoraPagerBoard::begin() now drives the full
vendor rail set including the display reset pulse and parks shared-SPI
selects high before first bus traffic.
Boot logo, full LVGL UI, QWERTY keyboard navigation, and rotary encoder
nav/select are now verified working on real hardware. Trackers updated:
Milestone 7's UI portion is done; the remaining radio/USB-companion/SD
gates move to a new Milestone 7b so they don't block Milestone 8's
on-device UI pass, which is now active.
All three envs (Heltec V4, T-Deck, pager) build green.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
PagerKeyboard.{h,cpp}: TCA8418 matrix keyboard over I2C. Unlike the
T-Deck's keyboard (a second MCU that resolves ASCII itself), the
TCA8418 only reports raw row/col events, so the keymap and
shift/sym/alt state machine live here -- keymap tables cribbed from
trail-mate's LilyGoKeyboard (same physical PCB). Press/release
polarity verified against the TCA8418 datasheet directly, since it
disagrees with the Adafruit library's own header comment. Backlight is
direct LEDC PWM on GPIO 46, using this framework version's actual
channel-based API (confirmed before writing the call, not assumed).
PagerEncoder.{h,cpp}: true A/B quadrature decode via a standard
Gray-code transition table, ISR-cheap-arithmetic-only like
TDeckTrackball's pattern (that driver's 4 discrete direction pins
aren't actually quadrature, so its exact shape doesn't transfer, only
the ISR/snapshot-read style does). Detent scaling (4 raw transitions
per detent) is an unverified assumption pending hardware bring-up.
Both gated on HAS_PAGER_KEYBOARD/HAS_PAGER_ENCODER, already reached by
every env's existing helpers/input build filter. All three envs build
green.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
[env:tlora_pager_lr1121_companion_radio_touch], cloned from the T-Deck
env with board/radio/display/GPS deltas for the LR1121 + ST7796 pager.
Two structural fixes were needed to actually get this to compile:
- pins_arduino.h moves to its own variants/lilygo_tlora_pager_pins/
folder (board JSON's "variant" field updated to match). PlatformIO's
arduino-esp32 build script unconditionally compiles every source
file under board_build.variants_dir/<board.variant>/ as a separate
framework-level library with none of our own lib_deps -- since this
board (unlike T-Deck/Heltec, which point at framework-bundled
variants) has no framework-bundled variant of its own, our
variants_dir override was colliding with our own board-glue files
and failing to find Wire.h/RadioLib.h.
- CustomLR1121Wrapper.h's bare quoted includes of RadioLibWrappers.h/
LR11x0Reset.h only resolve for core-lib files living in the same
directory as their targets; switched to angle-bracket includes with
the full core-lib subpath.
Also required one small, forced addition to UITask.cpp: its display
class selection only recognized the Tanmatsu vs. everything-else split,
which made this env's own hard compile gate unreachable. Added a single
#elif arm for the pager's display type: no other UITask.cpp behavior
changes, indev/resolution/layout wiring is still a later milestone.
All three envs (Heltec V4, T-Deck, pager) build green.
Signed-off-by: Tesso M Costa <tesso.martins@gmail.com>
New board: ThinkNode_M9_companion_radio_touch env, variants/thinknode_m9/
(board glue, LR1110 target, keyboard driver, partitions, M9_PORT.md pin
reference), boards/thinknode_m9.json, device_caps HAS_THINKNODE_M9 block,
HAS_M9_KEYBOARD input path in the touch UI (d-pad focus nav, tab jump keys,
QWERTY typing).
Based on a contributed bring-up patch by ded (SalishMesh), who also remote-
tested every build on a preproduction unit. Hard-won fixes on top of the
patch, each verified on hardware:
- LR1110 radio init -706: preprod chips run transceiver FW 0x0303, which
rejects DriveDiosInSleepMode (0x012A, added in FW 0x0308) that RadioLib
7.x sends unconditionally during begin(). New build-time patch
scripts/build/patch_radiolib_lr11x0.py tolerates it on old FW;
radio_init() prints the chip's device/FW/errors either way.
- TCXO: DIO3 at 3.3 V (the patch's active-oscillator/tcxo=0 theory gave
-707 on hardware).
- Display: rotation 1 (not 3), plus the missing landscape s_ui_rotation
override so LVGL renders 320x240 instead of portrait-into-landscape.
- Keyboard: the controller is a separate ESP32-S2 I2C slave (0x6C) with
addressed registers - reads select register 0x01 first (bare reads
return the HW-version register forever). Boot probe logs the
controller's HW/FW; backlight duty register wired.
- USB pad release: the keyboard bus lives on GPIO20/21 = the S3's native
USB D-/D+ pads, owned from reset by the ROM USB-Serial-JTAG (D+ pullup
on SDA). M9Board::begin() releases them before any bus init.
- GPIO35-37 are octal-PSRAM pins on the S3R8 - never drive them (the
patch's "SD CS = 36" misread package pin 36 = GPIO48; SD is on the
shared SPI bus, support returns with PIN_SD_CS=48 later).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
- History flush runs on the core-0 worker (snapshot + storage-busy gate +
bounded shutdown wait): kills the V4's multi-second ui:hist stalls and
the refuses-to-wake-after-message symptom (SPIFFS GC off the UI thread).
- BLE + Wi-Fi runtime enables share the boot co-init heap guard (50 KB
free + 20 KB block): refuse with a toast + revert the switch instead of
panicking (BLE) or silently not starting while claiming on (Wi-Fi).
- Internal DRAM: static footprint 95,365 -> 64,908 B (30.5 KB freed):
serial_interface -> PSRAM; 23 keyboard layout maps const'd -> flash;
nine rings/tables -> psAlloc PSRAM (UITask/TouchPrefsStore/MyMesh);
unused TinyUSB MSC + DFU-mode class drivers stubbed out of the link
(usb_unused_class_stubs.c) — CDC + runtime-DFU untouched, double-flash
verified over the stubbed stack.
- DataStore prefs writes are crash-safe (write .tmp, swap) with a
self-healing loader (.tmp recovery) and a truthful save result up to
the profile-name toast — fixes the boots-with-default-name-once report.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Consumes the new core (buffered receive drain task + RX counters, #13
stock payload layout, GPS-date guard). Fork side:
- TouchPrefs v33 rx_queue, DEFAULT ON for the test channel (fresh
installs + a one-time migrate for upgraders); opt-out toggle
'Buffered receive (experimental)' in Radio & Mesh, applies live.
- About live tier shows LoRa RX heard/read/err/late-lost/qdrop, the
field evidence for the missed-messages fix.
- Spectrum parks/resumes the drain task around raw radio use; MyMesh
setParams sequences hold the radio mutex.
- TanmatsuLoraRadio: no-op API stubs (P4 keeps its own RX path).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
New: stable/test update channels with an opt-in "Get test builds (beta)" toggle on
OTA devices (switches both the update check and what you install); experimental
opt-in MQTT bridge (consent-gated, payload encryption, direct messages off by
default); Portugal (Narrow) region preset (#74); saved-contacts counter in the
Contacts overflow menu (#72).
Fixed: the signal probe is now strictly zero-hop so a repeater can't re-flood it;
the contact list sorts before capping so the most relevant contacts show, with a
"+N more — search to narrow" footer (#73); the blocked-users list opened from
Contacts shows the two-line title bar with a back button; the Contacts overflow
popup fits the screen again.
Also lands the two-channel release tooling (scripts/release.sh stable/beta modes +
gen-flasher-meta channel arg), the docs site, and the MQTT reference decryptor.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Heltec V4 Expansion Kit local-sensor UI, board-gated behind HAS_EXPANSION_KIT
(V4 touch env only — T-Deck/Tanmatsu unaffected): a Sensors bottom tab
(atmosphere / GPS / battery + history charts), a Home env summary widget, an
Expansion Kit card in Device settings, and a Local Sensors detail page. Reads
on-board MeshCore sensors (BME280, SHT4x, battery, GPS, buzzer) via the standard
sensor/telemetry API — no new hardware drivers.
Mesh console: enable the existing Terminal on the V4 (HAS_TOUCH_UI), renamed
"Mesh console", with wifi/tcp/ble on-off + ota status quick commands. The
SD-backed file-manager pieces stay T-Deck-only (V4/Tanmatsu get a no-op path).
Tab indices are conditional so non-Expansion boards keep 5 tabs (Settings=4) and
the V4 gets 6 (Sensors=4, Settings=5). The PR's GPS-nav/waypoint and weather
pressure-alarm bundles were intentionally left out.
Ported from PR #29 by @samuelcoustet, re-applied against current main.
Co-Authored-By: samuelcoustet <257299705+samuelcoustet@users.noreply.github.com>
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
- enableTcp() now calls startTcpServer(false) directly instead of relying
on the main loop — fixes TCP not restarting when wifi_started is false
(BLE-only mode, radio toggled off, or cold re-enable from USB).
- Add touchHasOtaUpdateSlot() guard to the OTA button creation block so
the update affordances stay hidden under Launcher (single app slot),
where ota url would fail silently.
- Fix toggleTcpCb alert race: snapshot isTcpEnabled() before the toggle
so the alert text reflects the transition, not a post-action re-read
that could mismatch during OTA suspension.
- Replace global -w with -Wno-deprecated-declarations -Wno-unused-parameter
in both touch environments to keep third-party lib noise down while
surfacing real regressions in OTA, network, and companion paths.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- BLE: user-settable 6-digit pairing code (Settings -> Bluetooth), MyMesh::setBLEPin.
- Lock wallpaper: pick via the file manager (fast, any folder) + 'Set as wallpaper'
in the image viewer; downscaling JPEG decoder accepts images > 1024 px and keeps
the held buffer small; clear message for progressive JPEGs.
- Map tiles: validate JPEG magic before caching + re-fetch bad cached tiles
(fixes black quadrants).
- Channel @reply: quick-reply now appends at the cursor instead of wiping the
mention.
- Audio: heap pre-flight before i2s_driver_install (fixes the esp_timer NO_MEM
abort when toggling sound under BLE+Wi-Fi memory pressure).
- App drawer: squircle tiles. Log hygiene: CORE_DEBUG_LEVEL 1->0 (mute benign
vfs/Preferences spam off the USB-CDC companion stream).
- Core bump to core-v1.16.4 (drops the 4-byte chat-payload trailer, issue #13).
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Core bump: lib_deps -> meshcomod core-v1.16.3 (BLE advertises the node
name not "NimBLE"; GPS won't push a pre-fix ~1902 date).
Tim's quick-wins: Enter-key-sends toggle, 12-hour clock, lock-when-screen-off,
reverse scrollball.
Launcher / map: fix Wi-Fi tiles never downloading under Launcher (the SD-fallback
cache made tilesFsLowSpace() read the unmounted LittleFS as "full"); plot contact
markers before the tile decode so dots aren't ~2s late.
RTC / time: anchored-time guard re-applies UTC when the clock reads garbage
(GPS clobber); blank pre-2020 timestamps so empty channels don't show 1969/1970;
timezone picker (named zones with correct DST) replacing the CET-only base, with
a v2->v3 config migration mapping prior manual offsets onto a Custom zone.
BLE: persist the random pairing PIN (was re-rolled every boot).
Chat: don't auto-jump to latest on a new message when scrolled up; block-by-name
for non-contact room/channel senders (un-blockable room bots).
Power: drop CPU to 80 MHz when the screen is off; enable Wi-Fi modem-sleep only
once associated (enabling it on the unassociated STA broke the setup-wizard scan).
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
The T-Deck env had SX126X_DIO2_AS_RF_SWITCH=false, so std_init() called
setDio2AsRfSwitch(false). On the T-Deck the SX1262's antenna TX/RX switch is
driven ONLY by DIO2 (no external PA, no TXEN/RXEN pins), so disabling it strands
the +22 dBm PA off the antenna — ~16 dB loss, ~4 mW radiated. That matches the
reported measurement and likely why some sends weren't propagating. Flip to true.
Cross-checked: Meshtastic's T-Deck variant enables it, as does the Heltec V4 here
and every other SX1262 variant in the MeshCore lib — the T-Deck (copied from
upstream MeshCore's identically-buggy lilygo_tdeck variant) was the lone outlier.
LORA_TX_POWER=22, CURRENT_LIMIT=140 and the 1.8 V TCXO were already correct.
Needs an on-air re-measure (no RF meter here); the reporter offered to test.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Picks up the ESP32Board.h fix that seeds the time floor after any reset (not just
power-on), so the touch firmware no longer shows bogus 1970 timestamps after a
panic/OTA reboot until Wi-Fi/GPS sets the clock.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
wadamesh now builds its MeshCore core from the ALLFATHER-BV/meshcomod monorepo
(the same repo as the non-touch firmware) via a lean, source-only core-* tag,
instead of the separate meshcomod-core fork. The 8 touch-app files this repo
vendors are excluded from the lib with -DMC_VENDORED_TOUCH_APP. Build is
byte-identical (Heltec flash 2625757, unchanged). One core, one repo.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Adds the portable merge-bin.py post-script (app-bin -> out/ + a 'mergebin' custom
target) and enables it in both touch envs. Each board now produces firmware.bin
(app/OTA slot) and firmware-merged.bin (full install @ 0x0) — the two artifacts a
release ships. Verified: V4 merged 2.66 MB, T-Deck merged 2.88 MB.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
The earlier rename/minimize edits matched only the V4 env's formatting and
silently skipped the T-Deck env, leaving it on MeshCore.git#v1.16.0-wada.0 (old
name, pre-minimize tag whose fork still carried the 26 relocated files — a
duplicate-symbol hazard). Both envs now pin meshcomod-core@v1.16.0-wada.1;
T-Deck clean-rebuilds green + size-identical against it.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
The core fork was renamed to ALLFATHER-BV/meshcomod-core to make its lineage
explicit — it carries meshcomod's full core (protocol superset + Wi-Fi/BLE/UI
hooks), packaged as a library. Both envs now pin meshcomod-core @ v1.16.0-wada.1.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
Take ownership of the 26 files moved out of the core during the fork-minimize:
touch HW drivers (helpers/input/*), touch prefs/SD helpers + companion transport
servers + HTTP-OTA helpers (helpers/esp32/*, helpers/*Ota*.h), LVGL PSRAM
allocator, and touch diag. Three transport headers switched to lib-style
<helpers/...> includes for the new layout. platformio.ini builds them
(helpers/** filters + -I src) and pins MeshCore @ v1.16.0-wada.1 (the slimmed
fork). Both boards build green + size-identical from the published tag.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
Second board. Flattened env LilyGo_TDeck_companion_radio_touch (GT911 touch +
matrix keyboard + trackball, ST7789 via Adafruit, sensors off except GPS),
building green against MeshCore@v1.16.0-wada.0. Output byte-identical to the
in-tree meshcomod T-Deck build (delta = build-path strings).
Both touch boards now build from the published fork via lib_deps.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
First board lands. wadamesh builds the LVGL touch firmware as its own project,
consuming the MeshCore core via lib_deps @ git tag (ALLFATHER-BV/MeshCore
#v1.16.0-wada.0) — no vendored core in this repo. Output is byte-identical to the
in-tree meshcomod build (delta = embedded build-path strings only).
Contents: companion_radio app (MyMesh/main/DataStore), ui-touch LVGL UI,
variants/heltec_v4 board glue, boards/heltec_v4.json, lv_conf, the bundled
ed25519 lib, AsyncElegantOTA, partition table, and a flattened platformio.ini
for env heltec_v4_tft_companion_radio_usb_tcp_touch.
MeshCore-derived files (app glue) remain MIT; ui-touch is GPL — see NOTICE.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Signed-off-by: Kaj Schittecat <kaj@schittecat.com>
Pixel Perfect