Valentin V. Bartenev
46b0df7a4b
It's intended for Eastern Australia repeaters only. Using original EastMesh firmware is prefered in this case.
79 строки
2.3 KiB
Markdown
79 строки
2.3 KiB
Markdown
# MeshCoreTel Firmware
|
|
|
|
This is a fork of MeshCore-EastMesh firmware with MeshCoreTel broker support instead of EastMesh.
|
|
|
|
MeshCoreTel:
|
|
|
|
- <https://meshcoretel.ru/>
|
|
|
|
Original firmware (credits to Jared Dohrman, Scott Powell / Ripple Radios and the MeshCore contributors):
|
|
|
|
- <https://github.com/xJARiD/MeshCore-EastMesh>
|
|
|
|
MeshCoreTel firmware builds for MeshCore, with MQTT repeaters, WiFi companions, and simple release downloads for supported boards.
|
|
|
|
This repository keeps the upstream MeshCore firmware intact and adds an MeshCoreTel layer on top for packaging, release automation, WiFi-enabled companion builds, and MQTT-enabled repeater builds.
|
|
|
|
## Key MeshCoreTel Features
|
|
|
|
### MQTT Repeater Additions
|
|
|
|
- hardcoded broker support for:
|
|
- `meshcoretel`
|
|
- `letsmesh-eu`
|
|
- `letsmesh-us`
|
|
- WSS transport at `/mqtt`
|
|
- JWT auth using the device identity
|
|
- CLI controls for:
|
|
- WiFi credentials
|
|
- WiFi powersaving
|
|
- board battery reporting on supported targets
|
|
- MQTT endpoint enablement
|
|
- MQTT packet and raw publishing
|
|
- owner public key and email
|
|
- local web panel enablement
|
|
|
|
### Local Web Panel
|
|
|
|
On supported `*_repeater_mqtt` ESP32 targets, the repeater can expose a local HTTPS config panel over WiFi.
|
|
|
|
Features include:
|
|
|
|
- password-gated access using the existing repeater admin password
|
|
- allowlisted CLI execution
|
|
- grouped quick actions
|
|
- light and dark themes
|
|
- optional disable via `set web off`
|
|
|
|
Recommended use is initial setup and occasional troubleshooting. On MQTT repeater deployments, disable the panel again when finished if you want maximum MQTT heap headroom.
|
|
|
|
### Companion WiFi Additions
|
|
|
|
`*_companion_radio_wifi` targets now support persisted WiFi rescue commands:
|
|
|
|
- open a serial monitor at `115200` baud
|
|
- reboot the device
|
|
- long-press the user button within the first 8 seconds after boot to enter `CLI Rescue`
|
|
- wait for `========= CLI Rescue =========`
|
|
- send the commands from the serial monitor
|
|
|
|
These rescue commands are only available after entering `CLI Rescue`:
|
|
|
|
- `get wifi.status`
|
|
- `get wifi.ssid`
|
|
- `get wifi.powersaving`
|
|
- `set wifi.ssid <ssid>`
|
|
- `set wifi.pwd <password>`
|
|
- `set wifi.powersaving none|min|max`
|
|
|
|
## Status
|
|
|
|
Tested with my Heltec V4 OLED.
|
|
|
|
## Documentation
|
|
|
|
Current docs pages:
|
|
|
|
- [Home](./docs/index.md)
|
|
- [Custom CLI Commands](./docs/custom-cli.md)
|