diff --git a/variants/esp32/diy/hydra_868m/platformio.ini b/variants/esp32/diy/hydra_e22p_868m/platformio.ini
similarity index 84%
rename from variants/esp32/diy/hydra_868m/platformio.ini
rename to variants/esp32/diy/hydra_e22p_868m/platformio.ini
index ee37ee084..446bd0972 100644
--- a/variants/esp32/diy/hydra_868m/platformio.ini
+++ b/variants/esp32/diy/hydra_e22p_868m/platformio.ini
@@ -1,5 +1,5 @@
 ; Hydra - Meshtastic DIY v1 hardware with some specific changes
-[env:hydra_868m]
+[env:hydra_e22p_868m]
 custom_meshtastic_hw_model = 39
 custom_meshtastic_hw_model_slug = HYDRA
 custom_meshtastic_architecture = esp32
@@ -13,5 +13,4 @@ board = esp32doit-devkit-v1
 build_flags =
   ${esp32_base.build_flags}
   -D DIY_V1
-  -I variants/esp32/diy/hydra_868m
-  -D EBYTE_E22P_868M30S
+  -I variants/esp32/diy/hydra_e22p_868m
\ No newline at end of file
diff --git a/variants/esp32/diy/hydra_868m/variant.h b/variants/esp32/diy/hydra_e22p_868m/variant.h
similarity index 73%
rename from variants/esp32/diy/hydra_868m/variant.h
rename to variants/esp32/diy/hydra_e22p_868m/variant.h
index 27a93752d..5923cc766 100644
--- a/variants/esp32/diy/hydra_868m/variant.h
+++ b/variants/esp32/diy/hydra_e22p_868m/variant.h
@@ -20,8 +20,7 @@
 // Radio
 #define USE_SX1262 // E22-900M30S uses SX1262
 #define USE_SX1268 // E22-400M30S uses SX1268
-#define SX126X_MAX_POWER                                                                                                         \
-    22 // Outputting 22dBm from SX1262 results in ~30dBm E22-900M30S output (module only uses last stage of the YP2233W PA)
+#define SX126X_MAX_POWER 12 // Для модуля E22P 868M30S выходная мощность не более 12дбм! на выходе будет 30дбм!
 #define SX126X_DIO3_TCXO_VOLTAGE 1.8 // E22 series TCXO reference voltage is 1.8V
 
 #define SX126X_CS 18    // EBYTE module's NSS pin
@@ -32,16 +31,10 @@
 #define SX126X_BUSY 32  // EBYTE module's BUSY pin
 #define SX126X_DIO1 33  // EBYTE module's DIO1 pin
 
-//#define SX126X_TXEN 13 // Schematic connects EBYTE module's TXEN pin to MCU
-
-//#if defined(EBYTE_E22P_868M30S) // For Ebyte E22P-868M30S and E22P-915M30S modules - pin 14 always HIGH
-    #define SX126X_TXEN RADIOLIB_NC
-    #define SX126X_RXEN RADIOLIB_NC
-    #define SX126X_POWER_EN 14
-    #define SX126X_DIO2_AS_RF_SWITCH
-//#else
-//    #define SX126X_RXEN 14 // Schematic connects EBYTE module's RXEN pin to MCU
-//#endif
+#define SX126X_TXEN RADIOLIB_NC // Schematic connects EBYTE module's TXEN pin to MCU
+#define SX126X_RXEN RADIOLIB_NC
+#define SX126X_POWER_EN 14
+#define SX126X_DIO2_AS_RF_SWITCH
 
 #define LORA_CS SX126X_CS       // Compatibility with variant file configuration structure
 #define LORA_SCK SX126X_SCK     // Compatibility with variant file configuration structure
@@ -51,5 +44,4 @@
 #define LORA_TXEN SX126X_TXEN   // Compatibility with variant file configuration structure
 #define LORA_RXEN SX126X_RXEN   // Compatibility with variant file configuration structure
 #define LORA_RESET SX126X_RESET // Compatibility with variant file configuration structure
-#define LORA_DIO2 SX126X_BUSY   // Compatibility with variant file configuration structure
-#define LORA_POWER_EN SX126X_POWER_EN
\ No newline at end of file
+//#define LORA_DIO2 SX126X_BUSY   // Compatibility with variant file configuration structure
\ No newline at end of file