MeshCoreTel-firmware/variants/ikoka_handheld_nrf/variant.h

#ifndef _SEEED_XIAO_NRF52840_H_
#define _SEEED_XIAO_NRF52840_H_

/** Master clock frequency */
#define VARIANT_MCK       (64000000ul)

#define USE_LFXO      // Board uses 32khz crystal for LF
//#define USE_LFRC    // Board uses RC for LF

/*----------------------------------------------------------------------------
 *        Headers
 *----------------------------------------------------------------------------*/

#include "WVariant.h"

#ifdef __cplusplus
extern "C"
{
#endif // __cplusplus

#define PINS_COUNT              (33)
#define NUM_DIGITAL_PINS        (33)
#define NUM_ANALOG_INPUTS       (8)
#define NUM_ANALOG_OUTPUTS      (0)

// LEDs
#define PIN_LED                 (LED_RED)
#define LED_PWR                 (PINS_COUNT)
#define PIN_NEOPIXEL            (PINS_COUNT)
#define NEOPIXEL_NUM            (0)

#define LED_BUILTIN             (PIN_LED)

#define LED_RED                 (11)
#define LED_GREEN               (13)
#define LED_BLUE                (12)

#define LED_STATE_ON            (1)     // State when LED is litted

// Buttons
#define PIN_BUTTON1             (PINS_COUNT)

// Digital PINs
static const uint8_t D0  = 0 ;
static const uint8_t D1  = 1 ;
static const uint8_t D2  = 2 ;
static const uint8_t D3  = 3 ;
static const uint8_t D4  = 4 ;
static const uint8_t D5  = 5 ;
static const uint8_t D6  = 6 ;
static const uint8_t D7  = 7 ;
static const uint8_t D8  = 8 ;
static const uint8_t D9  = 9 ;
static const uint8_t D10 = 10;

#define VBAT_ENABLE             (14)    // Output LOW to enable reading of the BAT voltage.
                                        // https://wiki.seeedstudio.com/XIAO_BLE#q3-what-are-the-considerations-when-using-xiao-nrf52840-sense-for-battery-charging

#define PIN_CHARGING_CURRENT    (22)    // Battery Charging current
                                        // https://wiki.seedstudio.com/XIAO_BLE#battery-charging-current
// Analog pins
#define PIN_A0                  (0)
#define PIN_A1                  (1)
#define PIN_A2                  (2)
#define PIN_A3                  (3)
#define PIN_A4                  (4)
#define PIN_A5                  (5)
#define PIN_VBAT                (32)    // Read the BAT voltage.
                                        // https://wiki.seeedstudio.com/XIAO_BLE#q3-what-are-the-considerations-when-using-xiao-nrf52840-sense-for-battery-charging

#define BAT_NOT_CHARGING        (23)    // LOW when charging

#define AREF_VOLTAGE            (3.0)
#define ADC_MULTIPLIER          (3.0F) // 1M, 512k divider bridge

static const uint8_t A0  = PIN_A0;
static const uint8_t A1  = PIN_A1;
static const uint8_t A2  = PIN_A2;
static const uint8_t A3  = PIN_A3;
static const uint8_t A4  = PIN_A4;
static const uint8_t A5  = PIN_A5;

#define ADC_RESOLUTION          (12)

// Other pins
#define PIN_NFC1                (30)
#define PIN_NFC2                (31)

// Serial interfaces
#define PIN_SERIAL1_RX          (7)
#define PIN_SERIAL1_TX          (6)

// SPI Interfaces
#define SPI_INTERFACES_COUNT    (2)

#define PIN_SPI_MISO            (9)
#define PIN_SPI_MOSI            (10)
#define PIN_SPI_SCK             (8)

#define PIN_SPI1_MISO           (25)
#define PIN_SPI1_MOSI           (26)
#define PIN_SPI1_SCK            (29)

// Lora SPI is on SPI0
#define  P_LORA_SCLK            PIN_SPI_SCK
#define  P_LORA_MISO            PIN_SPI_MISO
#define  P_LORA_MOSI            PIN_SPI_MOSI

// Wire Interfaces
#define WIRE_INTERFACES_COUNT   (1)

#define PIN_WIRE_SDA            (6) // 4 and 5 are used for the sx1262 !
#define PIN_WIRE_SCL            (7) // use WIRE1_SDA

static const uint8_t SDA = (6);
static const uint8_t SCL = (7);

//#define PIN_WIRE1_SDA           (17)
//#define PIN_WIRE1_SCL           (16)
#define PIN_LSM6DS3TR_C_POWER   (15)
#define PIN_LSM6DS3TR_C_INT1    (18)

// PDM Interfaces
#define PIN_PDM_PWR	            (19)
#define PIN_PDM_CLK	            (20)
#define PIN_PDM_DIN	            (21)

// QSPI Pins
#define PIN_QSPI_SCK            (24)
#define PIN_QSPI_CS             (25)
#define PIN_QSPI_IO0            (26)
#define PIN_QSPI_IO1            (27)
#define PIN_QSPI_IO2            (28)
#define PIN_QSPI_IO3            (29)

// On-board QSPI Flash
#define EXTERNAL_FLASH_DEVICES  (P25Q16H)
#define EXTERNAL_FLASH_USE_QSPI

#ifdef __cplusplus
}
#endif

/*----------------------------------------------------------------------------
 *        Arduino objects - C++ only
 *----------------------------------------------------------------------------*/

#endif