Valentin V. Bartenev
1817248d97
Ported from meshcore-dev/MeshCore#2140 (Quency-D <hj_zzns@163.com>).
The upstream v1.16.0 merge changed the Heltec FEM LNA to disabled by
default (upstream commit 696aae6e). This patch restores the enabled
default for repeater via the new "radio.fem.rxgain" preference
(defaulted to 1), while also making the setting user-configurable
and persisted across reboots.
145 líneas
3.7 KiB
C++
145 líneas
3.7 KiB
C++
#include "T096Board.h"
|
|
|
|
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values come from variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void T096Board::initiateShutdown(uint8_t reason) {
|
|
#if ENV_INCLUDE_GPS == 1
|
|
pinMode(PIN_GPS_EN, OUTPUT);
|
|
digitalWrite(PIN_GPS_EN, !PIN_GPS_EN_ACTIVE);
|
|
#endif
|
|
variant_shutdown();
|
|
|
|
bool enable_lpcomp = (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT);
|
|
pinMode(PIN_BAT_CTL, OUTPUT);
|
|
digitalWrite(PIN_BAT_CTL, enable_lpcomp ? HIGH : LOW);
|
|
|
|
if (enable_lpcomp) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif // NRF52_POWER_MANAGEMENT
|
|
|
|
void T096Board::begin() {
|
|
NRF52Board::begin();
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
pinMode(P_LORA_TX_LED, OUTPUT);
|
|
digitalWrite(P_LORA_TX_LED, LOW);
|
|
|
|
periph_power.begin();
|
|
loRaFEMControl.init();
|
|
delay(1);
|
|
}
|
|
|
|
void T096Board::onBeforeTransmit() {
|
|
digitalWrite(P_LORA_TX_LED, HIGH); // turn TX LED on
|
|
loRaFEMControl.setTxModeEnable();
|
|
}
|
|
|
|
void T096Board::onAfterTransmit() {
|
|
digitalWrite(P_LORA_TX_LED, LOW); //turn TX LED off
|
|
loRaFEMControl.setRxModeEnable();
|
|
}
|
|
|
|
uint16_t T096Board::getBattMilliVolts() {
|
|
int adcvalue = 0;
|
|
analogReadResolution(12);
|
|
analogReference(AR_INTERNAL_3_0);
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
pinMode(PIN_BAT_CTL, OUTPUT);
|
|
digitalWrite(PIN_BAT_CTL, 1);
|
|
|
|
delay(10);
|
|
adcvalue = analogRead(PIN_VBAT_READ);
|
|
digitalWrite(PIN_BAT_CTL, 0);
|
|
|
|
return (uint16_t)((float)adcvalue * MV_LSB * 4.9);
|
|
}
|
|
void T096Board::variant_shutdown() {
|
|
nrf_gpio_cfg_default(PIN_VEXT_EN);
|
|
nrf_gpio_cfg_default(PIN_TFT_CS);
|
|
nrf_gpio_cfg_default(PIN_TFT_DC);
|
|
nrf_gpio_cfg_default(PIN_TFT_SDA);
|
|
nrf_gpio_cfg_default(PIN_TFT_SCL);
|
|
nrf_gpio_cfg_default(PIN_TFT_RST);
|
|
nrf_gpio_cfg_default(PIN_TFT_LEDA_CTL);
|
|
|
|
nrf_gpio_cfg_default(PIN_LED);
|
|
|
|
nrf_gpio_cfg_default(P_LORA_KCT8103L_PA_CSD);
|
|
nrf_gpio_cfg_default(P_LORA_KCT8103L_PA_CTX);
|
|
pinMode(P_LORA_PA_POWER, OUTPUT);
|
|
digitalWrite(P_LORA_PA_POWER, LOW);
|
|
|
|
digitalWrite(PIN_BAT_CTL, LOW);
|
|
nrf_gpio_cfg_default(LORA_CS);
|
|
nrf_gpio_cfg_default(SX126X_DIO1);
|
|
nrf_gpio_cfg_default(SX126X_BUSY);
|
|
nrf_gpio_cfg_default(SX126X_RESET);
|
|
|
|
nrf_gpio_cfg_default(PIN_SPI_MISO);
|
|
nrf_gpio_cfg_default(PIN_SPI_MOSI);
|
|
nrf_gpio_cfg_default(PIN_SPI_SCK);
|
|
|
|
// nrf_gpio_cfg_default(PIN_GPS_PPS);
|
|
nrf_gpio_cfg_default(PIN_GPS_RESET);
|
|
nrf_gpio_cfg_default(PIN_GPS_EN);
|
|
nrf_gpio_cfg_default(PIN_GPS_RX);
|
|
nrf_gpio_cfg_default(PIN_GPS_TX);
|
|
}
|
|
|
|
void T096Board::powerOff() {
|
|
#if ENV_INCLUDE_GPS == 1
|
|
pinMode(PIN_GPS_EN, OUTPUT);
|
|
digitalWrite(PIN_GPS_EN, !PIN_GPS_EN_ACTIVE);
|
|
#endif
|
|
loRaFEMControl.setSleepModeEnable();
|
|
variant_shutdown();
|
|
sd_power_system_off();
|
|
}
|
|
|
|
const char* T096Board::getManufacturerName() const {
|
|
return "Heltec T096";
|
|
}
|
|
|
|
bool T096Board::setLoRaFemLnaEnabled(bool enable) {
|
|
if (!loRaFEMControl.isLnaCanControl()) {
|
|
return false;
|
|
}
|
|
|
|
loRaFEMControl.setLNAEnable(enable);
|
|
loRaFEMControl.setRxModeEnable();
|
|
return true;
|
|
}
|
|
|
|
bool T096Board::canControlLoRaFemLna() const {
|
|
return loRaFEMControl.isLnaCanControl();
|
|
}
|
|
|
|
bool T096Board::isLoRaFemLnaEnabled() const {
|
|
return loRaFEMControl.isLNAEnabled();
|
|
}
|