MeshCoreTel-firmware/variants/xiao_nrf52/XiaoNrf52Board.cpp

#ifdef XIAO_NRF52

#include <Arduino.h>
#include <Wire.h>
#include <bluefruit.h>

#include "XiaoNrf52Board.h"

static BLEDfu bledfu;

static void connect_callback(uint16_t conn_handle) {
  (void)conn_handle;
  MESH_DEBUG_PRINTLN("BLE client connected");
}

static void disconnect_callback(uint16_t conn_handle, uint8_t reason) {
  (void)conn_handle;
  (void)reason;

  MESH_DEBUG_PRINTLN("BLE client disconnected");
}

void XiaoNrf52Board::begin() {
  NRF52BoardDCDC::begin();

  pinMode(PIN_VBAT, INPUT);
  pinMode(VBAT_ENABLE, OUTPUT);
  digitalWrite(VBAT_ENABLE, HIGH);

#ifdef PIN_USER_BTN
  pinMode(PIN_USER_BTN, INPUT_PULLUP);
#endif

#if defined(PIN_WIRE_SDA) && defined(PIN_WIRE_SCL)
  Wire.setPins(PIN_WIRE_SDA, PIN_WIRE_SCL);
#endif

  Wire.begin();

#ifdef P_LORA_TX_LED
  pinMode(P_LORA_TX_LED, OUTPUT);
  digitalWrite(P_LORA_TX_LED, HIGH);
#endif

  //  pinMode(SX126X_POWER_EN, OUTPUT);
  //  digitalWrite(SX126X_POWER_EN, HIGH);
  delay(10); // give sx1262 some time to power up
}

bool XiaoNrf52Board::startOTAUpdate(const char *id, char reply[]) {
  // Config the peripheral connection with maximum bandwidth
  // more SRAM required by SoftDevice
  // Note: All config***() function must be called before begin()
  Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
  Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);

  Bluefruit.begin(1, 0);
  // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
  Bluefruit.setTxPower(4);
  // Set the BLE device name
  Bluefruit.setName("XIAO_NRF52_OTA");

  Bluefruit.Periph.setConnectCallback(connect_callback);
  Bluefruit.Periph.setDisconnectCallback(disconnect_callback);

  // To be consistent OTA DFU should be added first if it exists
  bledfu.begin();

  // Set up and start advertising
  // Advertising packet
  Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
  Bluefruit.Advertising.addTxPower();
  Bluefruit.Advertising.addName();

  /* Start Advertising
    - Enable auto advertising if disconnected
    - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
    - Timeout for fast mode is 30 seconds
    - Start(timeout) with timeout = 0 will advertise forever (until connected)

    For recommended advertising interval
    https://developer.apple.com/library/content/qa/qa1931/_index.html
  */
  Bluefruit.Advertising.restartOnDisconnect(true);
  Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
  Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
  Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds

  strcpy(reply, "OK - started");

  return true;
}

#endif