MeshCoreTel-firmware/docs/custom-cli.md

Custom CLI Commands

This page covers the EastMesh-specific CLI commands added in this repository.

It does not try to repeat the full upstream MeshCore CLI surface.

Repeater MQTT Commands

These commands are available on *_repeater_mqtt firmware targets.

MQTT Status And Routing

• get mqtt.status: shows WiFi, NTP, IATA, endpoint status, status publishing state, and TX state.
• get mqtt.statuscfg: shows whether periodic status messages are enabled as a simple on or off value. Most users can just use get mqtt.status.
• get mqtt.iata: shows the IATA/location code used in MQTT topics.
• set mqtt.iata <code>: sets the IATA/location code, for example MEL.

MQTT Identity

• get mqtt.owner: shows the configured owner public key.
• set mqtt.owner <64-hex-char-public-key>: sets the owner public key used in JWT metadata.
• mqtt.owner <64-hex-char-public-key>: shorthand for setting the owner public key.
• get mqtt.email: shows the configured owner email.
• set mqtt.email <email>: sets the owner email used in JWT metadata.
• mqtt.email <email>: shorthand for setting the owner email.

MQTT Message Controls

• get mqtt.packets: shows whether packet messages are published.
• set mqtt.packets on|off: enables or disables packet publishing.
• get mqtt.raw: shows whether raw packet payloads are published.
• set mqtt.raw on|off: enables or disables the separate raw MQTT topic.
• set mqtt.status on|off: enables or disables periodic MQTT status publishing.
• get mqtt.tx: shows whether TX packets are included.
• set mqtt.tx on|off: enables or disables TX packet publishing.

MQTT Endpoints

• get mqtt.eastmesh-au
• set mqtt.eastmesh-au on|off
• get mqtt.letsmesh-eu
• set mqtt.letsmesh-eu on|off
• get mqtt.letsmesh-us
• set mqtt.letsmesh-us on|off

Legacy dotted aliases are also accepted:

• mqtt.eastmesh.au
• mqtt.letsmesh.eu
• mqtt.letsmesh.us

WiFi Settings For MQTT Repeaters

• get wifi.status: shows SSID, connection state, raw WiFi status code, and IP when connected.
• get wifi.ssid: shows the configured WiFi SSID.
• set wifi.ssid <ssid>: sets the WiFi SSID.
• set wifi.pwd <password>: sets the WiFi password.
• get wifi.powersaving: shows the current WiFi power save mode.
• set wifi.powersaving none|min|max: sets WiFi power saving mode.

Web Panel Controls

• get web
• get web.status: shows whether the local HTTPS panel is available.
• set web on|off
• set.web on|off: enables or disables the local HTTPS panel.

Runtime Diagnostics

• memory: shows current heap and PSRAM usage.
• stats-core: shows battery, uptime, sticky error count, and outbound queue depth.
• stats-radio: shows radio noise floor, last RSSI, last SNR, and TX/RX airtime.
• stats-packets: shows packet receive/send totals, flood/direct breakdown, and receive errors.

Board Battery Reporting

• get battery.reporting: shows whether board battery reporting is enabled. Support is board-dependent.
• set battery.reporting on|off: enables or disables battery voltage reporting on supported boards. This is currently useful for Heltec V3 boards where USB-only power can produce misleading battery readings. If your board needs this too, open an issue and support can be added board-by-board.

Web Panel Allowlisted Commands

When the repeater web panel is enabled, it only allows a limited command set.

That allowlist currently includes:

• clock
• get mqtt.status
• get web
• get web.status
• advert
• reboot
• start ota
• memory
• stats-core
• stats-radio
• stats-packets
• get wifi.status
• get wifi.powersaving
• get mqtt.iata
• set mqtt.iata <code>
• get mqtt.owner
• set mqtt.owner <64-hex-char-public-key>
• get mqtt.email
• set mqtt.email <email>
• get mqtt.packets
• set mqtt.packets on|off
• get mqtt.raw
• set mqtt.raw on|off
• get mqtt.statuscfg
• set mqtt.status on|off
• get mqtt.tx
• set mqtt.tx on|off
• get mqtt.eastmesh-au
• set mqtt.eastmesh-au on|off
• get mqtt.letsmesh-eu
• set mqtt.letsmesh-eu on|off
• get mqtt.letsmesh-us
• set mqtt.letsmesh-us on|off
• set web on|off
• get name
• set name <device-name>
• get lat
• set lat <latitude>
• get lon
• set lon <longitude>
• get guest.password
• set guest.password <password>
• set prv.key <64-hex-char-private-key>
• get advert.interval
• set advert.interval <minutes>
• get flood.advert.interval
• set flood.advert.interval <hours>
• get flood.max
• set flood.max <count>
• get owner.info
• set owner.info <text>

Companion WiFi Rescue Commands

These commands are available in the serial rescue CLI for *_companion_radio_wifi builds.

To enter CLI Rescue:

• open a serial monitor at 115200 baud

• reboot the device

• long-press the user button within the first 8 seconds after boot

• wait for ========= CLI Rescue =========

• get wifi.status: shows configured SSID, connection status, raw WiFi status code, and IP when connected.

• get wifi.ssid: shows the configured WiFi SSID.

• get wifi.powersaving: shows the current WiFi power saving mode.

• set wifi.ssid <ssid>: saves a WiFi SSID and immediately retries connection.

• set wifi.pwd <password>: saves a WiFi password and immediately retries connection.

• set wifi.powersaving none|min|max: changes the WiFi power save mode.

Companion WiFi builds also still support the existing rescue commands such as:

• set pin <6-digit-pin>
• rebuild
• erase
• ls ...
• cat ...
• rm ...
• reboot