MeshCoreTel-firmware/variants/t1000-e/T1000eBoard.cpp

#include <Arduino.h>
#include "T1000eBoard.h"
#include <Wire.h>

#include <bluefruit.h>

void T1000eBoard::begin() {
  NRF52Board::begin();
  btn_prev_state = HIGH;

  // Enable DC/DC converter for improved power efficiency
  uint8_t sd_enabled = 0;
  sd_softdevice_is_enabled(&sd_enabled);
  if (sd_enabled) {
    sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE);
  } else {
    NRF_POWER->DCDCEN = 1;
  }

#ifdef BUTTON_PIN
  pinMode(BATTERY_PIN, INPUT);
  pinMode(BUTTON_PIN, INPUT);
  pinMode(LED_PIN, OUTPUT);
#endif

#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
  Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
#endif

  Wire.begin();

  delay(10);   // give sx1262 some time to power up
}

#if 0
static BLEDfu bledfu;

static void connect_callback(uint16_t conn_handle) {
  (void)conn_handle;
  MESH_DEBUG_PRINTLN("BLE client connected");
}

static void disconnect_callback(uint16_t conn_handle, uint8_t reason) {
  (void)conn_handle;
  (void)reason;

  MESH_DEBUG_PRINTLN("BLE client disconnected");
}


bool TrackerT1000eBoard::startOTAUpdate(const char* id, char reply[]) {
  // Config the peripheral connection with maximum bandwidth
  // more SRAM required by SoftDevice
  // Note: All config***() function must be called before begin()
  Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
  Bluefruit.configPrphConn(92, BLE_GAP_EVENT_LENGTH_MIN, 16, 16);

  Bluefruit.begin(1, 0);
  // Set max power. Accepted values are: -40, -30, -20, -16, -12, -8, -4, 0, 4
  Bluefruit.setTxPower(4);
  // Set the BLE device name
  Bluefruit.setName("T1000E_OTA");

  Bluefruit.Periph.setConnectCallback(connect_callback);
  Bluefruit.Periph.setDisconnectCallback(disconnect_callback);

  // To be consistent OTA DFU should be added first if it exists
  bledfu.begin();

  // Set up and start advertising
  // Advertising packet
  Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
  Bluefruit.Advertising.addTxPower();
  Bluefruit.Advertising.addName();

  /* Start Advertising
    - Enable auto advertising if disconnected
    - Interval:  fast mode = 20 ms, slow mode = 152.5 ms
    - Timeout for fast mode is 30 seconds
    - Start(timeout) with timeout = 0 will advertise forever (until connected)

    For recommended advertising interval
    https://developer.apple.com/library/content/qa/qa1931/_index.html
  */
  Bluefruit.Advertising.restartOnDisconnect(true);
  Bluefruit.Advertising.setInterval(32, 244); // in unit of 0.625 ms
  Bluefruit.Advertising.setFastTimeout(30);   // number of seconds in fast mode
  Bluefruit.Advertising.start(0);             // 0 = Don't stop advertising after n seconds

  strcpy(reply, "OK - started");
  return true;
}
#endif