MeshCoreTel-firmware/variants/promicro/target.cpp

#include <Arduino.h>
#include "target.h"
#include <helpers/ArduinoHelpers.h>

#if ENV_INCLUDE_GPS
#endif

PromicroBoard board;

RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, SPI);

WRAPPER_CLASS radio_driver(radio, board);

VolatileRTCClock fallback_clock;
AutoDiscoverRTCClock rtc_clock(fallback_clock);
#if ENV_INCLUDE_GPS
  #include <helpers/sensors/MicroNMEALocationProvider.h>
  MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1);
  EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea);
#else
  EnvironmentSensorManager sensors;
#endif

#ifdef DISPLAY_CLASS
  DISPLAY_CLASS display;
#endif

#ifndef LORA_CR
  #define LORA_CR      5
#endif

bool radio_init() {
  rtc_clock.begin(Wire);
  
#ifdef SX126X_DIO3_TCXO_VOLTAGE
  float tcxo = SX126X_DIO3_TCXO_VOLTAGE;
#else
  float tcxo = 1.6f;
#endif

  SPI.setPins(P_LORA_MISO, P_LORA_SCLK, P_LORA_MOSI);
  SPI.begin();
  radio.setRfSwitchPins(SX126X_RXEN, SX126X_TXEN);
  int status = radio.begin(LORA_FREQ, LORA_BW, LORA_SF, LORA_CR, RADIOLIB_SX126X_SYNC_WORD_PRIVATE, LORA_TX_POWER, 8, tcxo);
  if (status == RADIOLIB_ERR_SPI_CMD_FAILED || status == RADIOLIB_ERR_SPI_CMD_INVALID) {
    #define SX126X_DIO3_TCXO_VOLTAGE (0.0f);
    tcxo = SX126X_DIO3_TCXO_VOLTAGE;
    status = radio.begin(LORA_FREQ, LORA_BW, LORA_SF, LORA_CR, RADIOLIB_SX126X_SYNC_WORD_PRIVATE, LORA_TX_POWER, 8, tcxo);
  }
  if (status != RADIOLIB_ERR_NONE) {
    Serial.print("ERROR: radio init failed: ");
    Serial.println(status);
    return false;  // fail
  }
  
  radio.setCRC(1);
  
#ifdef SX126X_CURRENT_LIMIT
  radio.setCurrentLimit(SX126X_CURRENT_LIMIT);
#endif
#ifdef SX126X_DIO2_AS_RF_SWITCH
  radio.setDio2AsRfSwitch(SX126X_DIO2_AS_RF_SWITCH);
#endif
#ifdef SX126X_RX_BOOSTED_GAIN
  radio.setRxBoostedGainMode(SX126X_RX_BOOSTED_GAIN);
#endif

  return true;  // success
}

uint32_t radio_get_rng_seed() {
  return radio.random(0x7FFFFFFF);
}

void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr) {
  radio.setFrequency(freq);
  radio.setSpreadingFactor(sf);
  radio.setBandwidth(bw);
  radio.setCodingRate(cr);
}

void radio_set_tx_power(uint8_t dbm) {
  radio.setOutputPower(dbm);
}

mesh::LocalIdentity radio_new_identity() {
  RadioNoiseListener rng(radio);
  return mesh::LocalIdentity(&rng);  // create new random identity
}